majver		equ	5		;version number of the infrastructure.

MAX_ADDR_LEN	equ	16		;maximum number of bytes in our address.

MAX_HANDLE	equ	8		;maximum number of handles.

MAX_P_LEN	equ	8		;maximum type length

MAX_MULTICAST	equ	8		;maximum number of multicast addresses.

;  Copyright, 1988, 1989, Russell Nelson

;   This program is free software; you can redistribute it and/or modify
;   it under the terms of the GNU General Public License as published by
;   the Free Software Foundation, version 1.
;
;   This program is distributed in the hope that it will be useful,
;   but WITHOUT ANY WARRANTY; without even the implied warranty of
;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
;   GNU General Public License for more details.
;
;   You should have received a copy of the GNU General Public License
;   along with this program; if not, write to the Free Software
;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

	.286

HT	equ	09h
CR	equ	0dh
LF	equ	0ah

;
;  Packet Driver Error numbers
NO_ERROR	equ	0		;no error at all.
BAD_HANDLE	equ	1		;invalid handle number
NO_CLASS	equ	2		;no interfaces of specified class found
NO_TYPE		equ	3		;no interfaces of specified type found
NO_NUMBER	equ	4		;no interfaces of specified number found
BAD_TYPE	equ	5		;bad packet type specified
NO_MULTICAST	equ	6		;this interface does not support
					;multicast
CANT_TERMINATE	equ	7		;this packet driver cannot terminate
BAD_MODE	equ	8		;an invalid receiver mode was specified
NO_SPACE	equ	9		;operation failed because of
					;insufficient space
TYPE_INUSE	equ	10		;the type had previously been accessed,
					;and not released.
BAD_COMMAND	equ	11		;the command was out of range, or not
					;implemented
CANT_SEND	equ	12		;the packet couldn't be sent (usually
					;hardware error)
CANT_SET	equ	13		;hardware address couldn't be changed
					;(more than 1 handle open)
BAD_ADDRESS	equ	14		;hardware address has bad length or
					;format

;a few useful Ethernet definitions.
RUNT		equ	60		;smallest legal size packet, no fcs
GIANT		equ	1514		;largest legal size packet, no fcs
EADDR_LEN	equ	6		;Ethernet address length.

;The following two macros are used to manipulate port addresses.
;Use loadport to initialize dx.  Use setport to set a specific port on
;the board.  setport remembers what the current port number is, but beware!
;setport assumes that code is being executed in the same order as the
;code is presented in the source file.  Whenever this assumption is violated,
;you need to enter another loadport.  Some, but not all examples are:
;in a loop with multiple setports, or a backward jump over a setport, or
;a forward jump over a setport.  If you have any doubt, consult the
;individual driver sources for examples of usage.  If you suspect that
;you have too few loadports, define the symbol "no_confidence".  This will
;force a loadport before every setport.
loadport	macro
	mov	dx,io_addr
port_no	=	0
	endm

;change the port number from the current value to the new value.
setport	macro	new_port_no
	ifdef	no_confidence		;define if you suspect that you don't
		loadport		;  have enough loadports, i.e. dx is
	endif				;  set to the wrong port.
	if	new_port_no - port_no EQ 1
		inc	dx
	else
		if	new_port_no - port_no EQ -1
			dec	dx
		else
			if	new_port_no - port_no NE 0
				add	dx,new_port_no - port_no
			endif
		endif
	endif
port_no	=	new_port_no
	endm

segmoffs	struc
offs		dw	?
segm		dw	?
segmoffs	ends